NS0-163 practice question 25 of 25
To remove a cluster setup, you must perform the following steps. 1. Type cf disable. 2. Unlicense cluster. 3. Remove partner entries for network interfaces from the /etc/rc file. 4. Halt and make sine the partner-sysid is blank. 5. Power down and remove the cluster interconnect card. 6. Perform steps 1-5 above on the partner node.
Full set: 186 questionsThe procedure outlined in the question correctly identifies the essential software and hardware steps required to dissolve a Data ONTAP 7-Mode high-availability (HA) pair and convert the nodes into standalone systems. Each step is a necessary component of the overall process:
1. cf disable: This command disables the cluster failover mechanism, which is the first logical step in separating the nodes.
2. Unlicense cluster: The cluster license key enables HA functionality and must be removed to revert to a standalone configuration.
3. Remove partner entries from /etc/rc: The /etc/rc file contains boot-time network configurations. Partner-specific interface configurations must be removed to prevent errors when the node boots without its partner.
4. Halt and clear partner-sysid: The partner-sysid is a critical boot environment variable that identifies the HA partner. It must be cleared on both nodes to break the cluster relationship at the hardware identity level. This is done from the boot loader prompt after halting the system.
5. Remove cluster interconnect: The physical interconnect (cables and/or card) provides the dedicated, high-speed link for the HA heartbeat and NVRAM mirroring. It must be physically disconnected or removed to sever the hardware link.
6. Perform on partner node: Since an HA pair consists of two nodes, the entire procedure must be replicated on the partner to complete the separation. While the exact sequence of these steps can vary slightly in practice, the set of actions listed is fundamentally correct and necessary to achieve the goal.
The alternative, "False," is incorrect because the list accurately enumerates the required tasks for decommissioning a 7-Mode HA pair. To claim the statement is false would imply that one or more of these steps are unnecessary or that the overall procedure is invalid, which is not the case according to official documentation.
1. NetApp Data ONTAP® 8.2
7-Mode System Administration Guide
Reference: Part 5
Chapter 22
"High-availability configuration and management
" section "Converting an HA pair to two standalone storage systems."
Content: This guide explicitly details the procedure. It instructs the administrator to: 1. cf disable on both nodes. 2. Halt both nodes. 3. At the LOADER prompt
set the partner system ID to null (setenv partner-sysid ""). 4. Disconnect the cluster interconnect cables. 5. Boot the nodes individually. 6. Edit the /etc/rc file to remove partner interface information. 7. Use the license delete command to remove the cluster license. This source validates that all steps mentioned in the question are required components of the official procedure.
2. NetApp Data ONTAP® 7.3
High-Availability Configuration Guide
Reference: Chapter 5
"Disabling a high-availability configuration
" section "Converting an HA pair to two standalone systems."
Content: This guide for an earlier version of ONTAP provides a nearly identical procedure
confirming the long-standing nature of these steps. It lists the following actions: disabling cluster failover (cf disable)
halting the nodes
clearing the partner-sysid at the boot prompt
disconnecting the interconnect
booting the systems
editing the /etc/rc file
and removing the cluster license. This corroborates that the actions in the question are correct and necessary.
Keep practicing
Take the free NS0-163 practice test
Ten exam-style questions with answers and explanations, plus the exam facts and study guides.
More questions
Other NS0-163 practice questions
- Question 1Which two tools should an administrator use to monitor system performance in real time? (…
- Question 2Which one of the following statements does not apply to the SnapMirror visibility-interva…
- Question 3Which one of the following statements apply to the Free Space Estimator utility?
- Question 4The required hardware to add SyncMirror to an existing Clustered Failover system consists…
- Question 5What is the maximum distance between a standard clustered pair?
- Question 6Which is true of the SnapVault backup of NetApp storage system?
