RCNI practice question 6 of 15
Which three objects can be assigned a Layer 3 address? (Choose three.)
Full set: 54 questionsOn RUCKUS ICX devices, a Layer 3 (IP) address can be assigned to logical or virtual interfaces to enable routing and IP-based management. Virtual Ethernet (VE): A VE is a logical Layer 3 interface that represents a specific VLAN, enabling inter-VLAN routing. Loopback: A loopback is a virtual interface that is always active. It is commonly used for stable router identification in routing protocols (like OSPF or BGP) and for management access. GRE tunnels: A Generic Routing Encapsulation (GRE) tunnel interface is a logical interface that encapsulates traffic over an IP network. The tunnel interface itself requires an IP address to establish the tunnel and route traffic through it.
A. Stack Interface: This is not a standard configurable Layer 3 interface. Management of a RUCKUS ICX stack is performed using an IP address assigned to a Virtual Ethernet or a dedicated management port.
B. VxLAN: VXLAN (Virtual Extensible LAN) is a Layer 2 overlay technology. While its tunnel endpoints (VTEPs) use Layer 3 addresses, the VXLAN segment (VNI) itself represents a Layer 2 domain.
C. Virtual LAN: A VLAN is a Layer 2 broadcast domain. To give it a Layer 3 presence for routing, you must create a corresponding Virtual Ethernet (VE) interface and assign the IP address to the VE.
1. Virtual Ethernet (VE): RUCKUS FastIron Layer 3 Routing Configuration Guide, 08.0.95 | Part Number: 53-1005930-01, Chapter 2: Configuring IP, Section: "Configuring a virtual routing interface", Page 33. "A virtual routing interface, also called a VE, is a logical Layer 3 interface that you can configure on a Layer 3 switch... You must assign an IP address to the virtual routing interface..."
2. Loopback: RUCKUS FastIron Layer 3 Routing Configuration Guide, 08.0.95 | Part Number: 53-1005930-01, Chapter 2: Configuring IP, Section: "Configuring a loopback interface", Page 37. "A loopback interface is a virtual interface that is always up... You can assign an IP address to a loopback interface."
3. GRE tunnels: RUCKUS FastIron Layer 3 Routing Configuration Guide, 08.0.95 | Part Number: 53-1005930-01, Chapter 10: Configuring Tunnels, Section: "Configuring a GRE tunnel", Page 218. The configuration example explicitly shows the ip address command being applied under the interface tunnel context.
4. VLAN vs. VE: RUCKUS FastIron Layer 2 Switching Configuration Guide, 08.0.95 | Part Number: 53-1005928-01, Chapter 3: Configuring VLANs, Page 43. This chapter describes VLANs as Layer 2 constructs. The Layer 3 configuration is handled by VE interfaces as documented in the Layer 3 guide.
5. Stack Management: RUCKUS FastIron Stacking Configuration Guide, 08.0.90 | Part Number: 53-1005561-01, Chapter 3: Stack Management, Section: "Stack management options", Page 37. This section details that stack management is achieved via the management port or an IP address on a VLAN (VE interface). It makes no mention of a configurable "stack-interface".
Keep practicing
Take the free RCNI practice test
Ten exam-style questions with answers and explanations, plus the exam facts and study guides.
More questions
Other RCNI practice questions
- Question 1Which two commands display Power over Ethernet (PoE) power budget? (Choose two.)
- Question 2What is the maximum distance between ICX devices in a stack?
- Question 3The root bridge is connected to another switch over two independent 10Gbe links. Which li…
- Question 4What are two features of Open Shortest Path First (OSPF)? (Choose two.)
- Question 5Which command enables global IPv6 capabilities?
- Question 7Which command can be used to identify Cyclic Redundancy Check (CRC) errors on port Ethern…
