CWDP-305 practice question 5 of 35
Why does a frame transmitted at 1 Mbps have a greater usable range than the same frame transmitted at 54 Mbps?
Full set: 341 questionsDomain WLAN Design and Site Surveying
The usable range of a wireless signal is determined by the link budget, a key component of which is the receiver's sensitivity. Receiver sensitivity is the minimum signal power required for the receiver to successfully decode the data. Lower data rates, such as 1 Mbps, use simple and robust modulation and coding schemes (e.g., DBPSK). These schemes can be correctly interpreted at a much lower Signal-to-Noise Ratio (SNR) compared to the complex schemes (e.g., 64-QAM) used for higher data rates like 54 Mbps. This means the receiver sensitivity requirement is lower (a more negative dBm value), allowing the signal to travel farther and weaken more before becoming unusable, thus extending the effective range.
A. Free space path loss is a function of frequency and distance, not the data rate or modulation complexity of the transmission.
C. 802.11 devices adapt to changing conditions primarily by shifting data rates, not by increasing transmit power as the rate decreases. Transmit power is constrained by regulatory limits.
D. All radio frequency (RF) waves propagate at the speed of light. Lower data rate frames occupy the medium for a longer duration, which increases the probability of collisions. ---
1. IEEE Std 802.11-2020, "Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications."
Section 16.4.8.1 (Receiver minimum input sensitivity - DSSS PHY): Specifies a minimum sensitivity of -80 dBm for a 1 Mbps data rate with a Packet Error Rate (PER) of no more than 8% for a 1024-byte packet.
Section 18.4.8.2 (Receiver minimum input sensitivity - ERP-OFDM PHY): Specifies a minimum sensitivity of -72 dBm for a 54 Mbps data rate with a PER of no more than 10% for a 1000-byte packet.
This standard directly shows that the sensitivity requirement for 1 Mbps is significantly lower (better) than for 54 Mbps, validating that a weaker signal can be received.
2. Goldsmith, A. (2005). Wireless Communications. Cambridge University Press.
Chapter 6, Section 6.1 (Digital Modulation): This chapter explains that as the size of a signal constellation increases (e.g., from BPSK with 2 points to 64-QAM with 64 points), the distance between points decreases. This requires a higher SNR at the receiver to distinguish between constellation points without errors, thus requiring a higher received signal power for the same bit-error rate. This directly supports why 54 Mbps (64-QAM) needs a stronger signal than 1 Mbps (DBPSK). (DOI: https://doi.org/10.1017/CBO9780511841224)
3. Mediatek, Inc. (2021). An Introduction to Wi-Fi Coexistence. White Paper.
Section "Receiver Sensitivity": "The receiver sensitivity is the lowest power level at which the receiver can detect an RF signal and demodulate data. It is expressed in dBm. The lower the value, the better the receiver sensitivity. For example, a receiver sensitivity of -98 dBm is better than -95 dBm. The receiver sensitivity is related to the data rate. The higher the data rate, the worse the receiver sensitivity."
This official vendor documentation confirms the inverse relationship between data rate and receiver sensitivity, which is the core principle of the correct answer.
Keep practicing
Take the free CWDP-305 practice test
Ten exam-style questions with answers and explanations, plus the exam facts and study guides.
More questions
Other CWDP-305 practice questions
- Question 1Using a SCA means that all APs will be using the same channel in a given layer. How is th…
- Question 2What two 802.11 amendments deal with regulatory and transmission requirements? Response:
- Question 3What type of protection should be provided to outdoor antenna installations? Response:
- Question 4What service must be implemented on your customer's network to authenticate users against…
- Question 6Prior to meeting with the customer for the first time, you should do which of the followi…
- Question 7You are conducting a physical site survey where heavy machinery is repaired. What is a co…
