CWNA-109 practice question 4 of 25
The BSA of an AP covers the area used by the sales and marketing department. Thirty-five stations operate in this space. The users indicate that they…
Full set: 122 questionsThe most cost-effective and recommended solution is to change the 5 GHz radio's channel width from 20 MHz to 40 MHz. This is a simple configuration change that costs nothing. For 802.11ac clients, doubling the channel width more than doubles the potential data rate, directly addressing the users' need for more throughput. Using 40 MHz channels in the 5 GHz band is a standard enterprise practice that provides a good balance between performance improvement and efficient spectrum management, leaving sufficient channels available for a multi-AP channel reuse plan.
A. Use a 160 MHz channel on the 5 GHz radio Using 160 MHz channels is not recommended in most enterprise environments as it consumes a massive amount of spectrum, severely limiting channel reuse and increasing the potential for co-channel interference.
C. Install a second AP in the coverage area This would increase capacity but is not the "least expensive" solution, as it requires purchasing and installing new hardware, whereas a configuration change is free.
D. Use a 40 MHz channel on the 2.4 GHz radio This is strongly discouraged. The 2.4 GHz band is narrow and crowded; using a 40 MHz channel would cause significant interference to neighboring Wi-Fi networks and is considered a "bad neighbor" practice. ---
1. Coleman, D. D., & Westcott, D. A. (2021). CWNA Certified Wireless Network Administrator Study Guide: Exam CWNA-109 (6th ed.). Wiley.
Page 368, Chapter 13 "802.11ac and 802.11ax": The text explains that 802.11ac introduced wider channels (20, 40, 80, and 160 MHz) in the 5 GHz band to increase throughput. It notes, "The main drawback of channel bonding is that it uses more frequency space... Using 80 MHz or 160 MHz channels can quickly use up the available spectrum in the 5 GHz UNII bands." This supports why 40 MHz (Option B) is a reasonable compromise, while 160 MHz (Option A) is often impractical.
Page 336, Chapter 12 "802.11n": Regarding 40 MHz channels in the 2.4 GHz band, the guide states, "Because of the potential for interference, many WLAN administrators choose to use only 20 MHz channels in the 2.4 GHz ISM band." This directly supports why Option D is not a recommended solution.
2. Cisco. (2023). Radio Resource Management: 2.4-GHz and 5-GHz Channel Width Configuration Best Practices. Cisco Community.
Section: "5-GHz Channel Width Best Practices": The document recommends, "For most enterprise deployments, it is recommended to use 40-MHz channels." It further cautions against 80 MHz and 160 MHz channels in dense environments due to the reduction in available non-overlapping channels, which validates the choice of 40 MHz (Option B) over 160 MHz (Option A).
3. Sikora, A., & Groza, V. Z. (2012). A study of the coexistence of 802.11 20 MHz and 40 MHz channels. IEEE Transactions on Instrumentation and Measurement, 61(6), 1703-1711. https://doi.org/10.1109/TIM.2011.2181871
Section III.B, "Coexistence Scenarios": This academic paper analyzes the performance degradation when 40 MHz channels are used in the crowded 2.4 GHz band. The findings support the industry best practice of avoiding 40 MHz channels in 2.4 GHz (Option D) due to the significant negative impact (interference) on adjacent 20 MHz networks.
Keep practicing
Take the free CWNA-109 practice test
Ten exam-style questions with answers and explanations, plus the exam facts and study guides.
More questions
Other CWNA-109 practice questions
- Question 1You manage a WLAN with 100 802.11ac access points. All access points are configured to us…
- Question 2You have implemented an 802.11ax WLAN for a customer. All APs are four stream HE APs. The…
- Question 3You are the network administrator for ABC Company. Your manager has recently attended a w…
- Question 5What is always required to establish a high quality 2.4 GHz RF link at a distance of 3 mi…
- Question 6You are troubleshooting a problem with interference from a non-802.11 device. Given that …
- Question 7You are implementing a VHT-capable AP. Which one of the following channels is available i…
