CWDP-305 practice question 15 of 35
An engineering firm just upgraded their WLAN form nine 802.11n APS to nine 802.11ac APs. After this upgrade, they did not see any improvement in throughput. What is the most likely cause of this result? Response:
Full set: 341 questionsDomain WLAN Design Troubleshooting
The most significant throughput gains from 802.11ac (Wi-Fi 5) are derived from features like wider channel widths (80 MHz and 160 MHz) and higher-order modulation (256-QAM). For these features to be utilized, both the Access Point (AP) and the client device must support the 802.11ac standard. If the clients were not upgraded and remain 802.11n-capable, they will connect to the new APs using the older 802.11n protocol. The performance of a wireless link is determined by the capabilities of the least capable device, meaning the network will continue to operate at 802.11n speeds, resulting in no observable throughput improvement.
A. The APs are still using the 5 GHz lower band 802.11ac operates exclusively in the 5 GHz band. Using lower band channels (e.g., UNII-1) does not prevent the use of 802.11ac features or a throughput increase over 802.11n.
C. APs are mounted on the wall While suboptimal mounting can affect antenna patterns and coverage, it is unlikely to be the primary cause for a complete lack of throughput improvement after a major technology upgrade.
D. APs are transmitting at a low transmit power Low transmit power primarily impacts range and signal strength. An 802.11ac client in close proximity to the AP could still achieve higher data rates, so this would not explain a total absence of improvement. ---
1. CWNP, CWDP-304 Certified Wireless Design Professional Official Study Guide, (Indianapolis: Wiley, 2021).
Page 54, Chapter 2, "Client Device Capabilities": The guide emphasizes that a WLAN design must account for the capabilities of the client devices. It states, "The capabilities of the client devices connecting to the WLAN are a key factor in the performance of the network... If the clients do not support the latest standards, the network will not perform at its highest potential." This directly supports that mismatched client capabilities are a primary performance limiter.
2. Cisco, "802.11ac: The Fifth Generation of Wi-Fi" White Paper, (2020).
Section: "What Do I Need to Do to Deploy 802.11ac?", Page 10: This official vendor document explicitly states, "To take advantage of the new speeds available with 802.11ac, both the AP and the client device must support 802.11ac." This confirms that the client upgrade is a mandatory prerequisite for seeing performance benefits.
3. IEEE Std 802.11ac™-2013, IEEE Standard for Information technology--Telecommunications and information exchange between systems Local and metropolitan area networks--Specific requirements Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications, Amendment 4: Enhancements for Very High Throughput for Operation in Bands below 6 GHz.
Clause 22, "VHT PHY specification": This entire clause details the physical layer enhancements for 802.11ac, such as 80/160 MHz channels and 256-QAM. The standard defines these as features of a Very High Throughput (VHT) station (STA). A connection can only use these features if both communicating STAs (the AP and the client) are VHT-capable.
Keep practicing
Take the free CWDP-305 practice test
Ten exam-style questions with answers and explanations, plus the exam facts and study guides.
More questions
Other CWDP-305 practice questions
- Question 1Using a SCA means that all APs will be using the same channel in a given layer. How is th…
- Question 2What two 802.11 amendments deal with regulatory and transmission requirements? Response:
- Question 3What type of protection should be provided to outdoor antenna installations? Response:
- Question 4What service must be implemented on your customer's network to authenticate users against…
- Question 5Why does a frame transmitted at 1 Mbps have a greater usable range than the same frame tr…
- Question 6Prior to meeting with the customer for the first time, you should do which of the followi…
