400-007 practice question 4 of 35

A service provider hires you to design its new managed CE offering to meet these requirements • The CEs cannot run a routing protocol with the PE •…

Full set: 397 questions
A service provider hires you to design its new managed CE offering to meet these requirements • The CEs cannot run a routing protocol with the PE • Provide the ability for equal or unequal ingress load balancing in dual-homed CE scenarios. • Provide support for IPv6 customer routes • Scale up to 250.000 CE devices per customer. • Provide low operational management to scale customer growth. • Utilize low-end (inexpensive) routing platforms for CE functionality. Which tunneling technology do you recommend?
Answer options
A: FlexVPN
B: point-to-point GRE
C: DMVPN
D: LISP Correct answer
Correct Answer:
D. LISP
Explanation

LISP (Locator/ID Separation Protocol) is uniquely suited to meet all the specified requirements. It decouples a device's identity (Endpoint ID or EID) from its location (Routing Locator or RLOC), creating a highly scalable overlay. CEs register their EID-to-RLOC mappings with a central mapping system, which eliminates the need for a traditional routing protocol between the CE and PE. This architecture offloads control plane complexity from the CEs, allowing the use of low-end devices. LISP natively supports sophisticated ingress load balancing (both equal and unequal) through configurable priority and weight values in the EID-to-RLOC mappings. The protocol is address-family agnostic, fully supporting IPv6, and is designed for internet-scale deployments, easily exceeding the 250,000 device requirement with low operational overhead.

Why Incorrect

A. FlexVPN: Fails the "no routing protocol" and "low operational management" requirements at this scale, as it would necessitate complex static routing or a disallowed routing protocol.
B. point-to-point GRE: Is not a scalable solution. Manually configuring and managing 250,000 static tunnels is operationally infeasible and violates the scalability and management requirements.
C. DMVPN: While scalable to a degree, it typically relies on a routing protocol over the overlay. Its hub-and-spoke control plane does not scale efficiently to 250,000 devices.

References

1. Cisco Systems

"LISP Traffic Engineering" in IP Routing: LISP Configuration Guide

Cisco IOS XE Gibraltar 16.11.x. This document explicitly details the use of priority and weight values for load balancing. It states

"You can influence the choice of an Egress Tunnel Router (ETR) that is used to reach a destination EID by configuring the priority and weight of the RLOCs that are associated with the EID-to-RLOC mapping." This directly addresses the load balancing requirement.

2. Farinacci

D.

Fuller

V.

Meyer

D.

& Lewis

D. (2013). RFC 6830: The Locator/ID Separation Protocol (LISP). IETF. Section 2

"Architectural Overview

" describes the fundamental separation of EIDs and RLOCs and the role of the EID-to-RLOC mapping system. This core concept is what allows LISP to operate without a traditional CE-PE routing protocol and achieve massive scale.

3. Cisco Live Presentation

BRKCRS-3435

"LISP - A Next Generation Networking Architecture" (2019). Slide 10

"LISP Key Benefits

" lists "Improved Scalability" and "Multi-homing/Traffic Engineering" as primary advantages. The presentation details how the mapping system (LISP's control plane) allows the data plane to scale independently

fitting the service provider requirements.

4. Cisco Press

LISP Network Implementation and Troubleshooting (2020)

Chapter 1

"LISP Fundamentals". This chapter explains that LISP was designed to solve routing scalability issues in the global Internet. It states

"LISP provides a flexible and scalable network virtualization overlay... without having to deploy a traditional control plane protocol like BGP between the edge devices and the provider core." This directly supports the "no routing protocol" and scalability requirements.

Scroll to Top